FLANGE AND JOINT INTEGRITY

/, Oil & Gas/FLANGE AND JOINT INTEGRITY
Date : a.15 – 18 October 2012
b.19 – 22 November 2012
c.10 – 13 December 2012
Duration : 4 Days
Venue : Hotel All Seasons, Yogyakarta
Investation Fee : IDR 7.250.000 (full fare)IDR 7.000.000 (earlybird)

IDR 6.750.000 (Group)

REGISTER ONLINE NOW

FLANGE AND JOINT INTEGRITY

 

INTRODUCTION:

In the oil & gas and petrochemical industries, compressors play important role to support all facilities and process that require pressurized gases. Furthermore, air or gas leakage is not acceptable since it affecting on productivity or safety. Hence compressor flange joint integrity should be taken into account.

The reliability of the flanged joint depends critically on competent control of the joint making process, alignment, assembly, and its measurement. It is common to put considerable effort into the design process only for improper assembly to lead to joint failure. Therefore it is important that joint making is undertaken by trained and validated technicians who have an understanding of the procedure and the underlying principles and practice.

To achieve better performance on flange joint, it is important to ensure that all individuals with responsibilities in connection with ensuring the safe control of flange joints are trained and validated as competent to undertake these responsibilities. The program is based around a presentation of best practices and utilizes an intelligent bolting system to explain and demonstrate these principles. This unique method allows key areas of joint making e.g. the need to use bolt lubricant, to be clearly understood.

TRAINING MATERIAL OUTLINE:

The training covers a broad spectrum of topics which can be tailored to suit requirements including:

  1. Introduction to compressor alignment and assembly
  2. Flange Joint Preparation and Assembly
  3. Flange design and standard
  4. Bolt and bolt joint
  5. Bolt and flange strength
  6. Stress Analysis and Tightening Joints
  7. Load control vs torque control
  8. Load and torque measurement
  9. Intelligent bolt control
  10. Protection and Maintenance

 

INSTRUCTOR :   Dr.Ir. Paryana Puspaputra, M.Eng., and Team

 

VENUE :   Hotel All Seasons, Yogyakarta

 

TRAINING DURATION :    4 days

 

TRAINING TIME :  

  1. 15 – 18 October 2012
  2. 19 – 22 November 2012
  3. 10 – 13 December 2012

 

INVESTATION PRICE/PERSON :    

  1. Rp 7.250.000/peserta (bayar penuh)  atau
  2. Rp 7.000.000/peserta (early bird, yang membayar 1 minggu sebelum training)  atau
  3. Rp 6.750.000/peserta (untuk peserta bergroup yang terdiri dari 3 orang peserta atau lebih dari 1 perusahaan yang sama)

 

FACILITIES FOR PARTICIPANTS:

  1. Training Module
  2. Flash Disk contains training material
  3. Certificate
  4. Stationeries: NoteBook and Ballpoint
  5. T-Shirt
  6. Backpack
  7. Training Photo
  8. Training room with Full AC facilities and multimedia
  9. Lunch and twice coffeebreak every day of training

10. Qualified Instructor

11. Transportation for participants from hotel of participants to/from hotel of training – VV (if minimal participants is 4 persons from the same company)

 

“TRAINING INSTRUCTOR”

Paryana Puspaputra was born in Kotabumi on January 19, 1964, is a Lecturer at the Department of Mechanical Engineering, Faculty of Industrial Technology, Indonesia Islamic University – Indonesia. Undergraduate from Department of Mechanical Engineering, Bandung Institute of Technology, Indonesia (ITB) in 1990 and master degree in Mechanical Engineering Department of Nagaoka University of Technology, Japan in 1996. He achieved his doctorate degree in Department of Mechanical Engineering, Bandung Institute of Technology, Indonesia (ITB) in 2012. He is also experienced as consultant and training instructure for several manufacturing and oil company, such as Chevron, Total, KPA, Petrokimia, Semen, Indonesia Power, etc. His background in mechanical equipment and machinery is completed with knowledge in instrumentation technology which was started from his final project in undergraduate by making software and data acquisition for predictive maintenance, and continued with his graduate thesis in control system for nano technology. There are researches and industrial implementation in data acquisition such as building the DNC system for production-shop using CNC machine, developing the balancing machine for Panasia Indosyntex – Bandung, SCADA system Development based on Fuji Electric control system (for IPAL – Pertamina – Cilacap, Toxic Gas Monitoring – Dieng – Central Java, etc). Moreover, he is also an official trainer of softwares for design and manufacturing base on CAD/CAM Technology (AutoCAD, Inventor, and Delcam PowerShape, ArtCAM) and familier with some finite element based analysys softwares such as Moldflow, ANSYS, SAP, CAESAR II, etc.

 

INFORMASI TRAINING KE:

PT.MAIRODI MANDIRI SEJAHTERA (MMS)
Telp/Fax: (022)7215668 atau (022)7215416

SMS Center : 081809600076 atau 02272282252 atau 081322050262 atau 085860263043 atau 085222155409

Email : training@mairodi-training.com atau ptmmsbdg@gmail.com

Website : http://mairodi-training.com

Contact Person : Wahyu H, Mira, Yanti Deris Sutanty, Aziz Aminudin

SILAHKAN ISI FORM REGISTRASI BERIKUT :


REGISTRASI

Judul Training

Tanggal Training

Jenis Pesan

Data Diri

Nama Anda (required)

Job Title (required)

Company (required)

Company Address

Email (required)

Website

Mobile Phone (required)

Office Phone

Extensions No

Faximile

DATA PRE REGISTRATION (Tidak Mengikat)

Jumlah Peserta (required)

Nama-nama Peserta

Pesan untuk Penyelenggara Training

Isi kode gambar di bawah ini :
captcha

No comments yet.

Leave a comment

Your email address will not be published.

*